VIAVI MAP mSRC-C2 MSRC-C23300HS-M100-MFA Dual 1310 nm High Power SLED Source Module

Dual-output 1310 nm high power SLED light source module for the VIAVI MAP platform with ≥ 10 dBm output power per source.

Center Wavelength: 1310 nm
Wavelength Tolerance: ±10 nm
Spectral Width (FWHM): < 60 nm
Output Optical Power: ≥ 10 dBm

Datasheet

Overview

The VIAVI MSRC-C23300HS-M100-MFA is a dual 1310 nm high power Super-Luminescent Light Emitting Diode (SLED) source module with FC/APC connectors. It belongs to the Multiple Application Platform (MAP) General Purpose Light Source family (mSRC-C2), a range of stabilized, fiber-coupled, fixed-wavelength emitters covering the key Telecom/Datacom wavelength bands.

SLED sources combine the broadband output of LEDs with the high output power of laser sources. The high power SLED variant is TEC stabilized, and optical isolators inside the module remove interference effects from external sources of reflection. The source can operate in constant current or constant power mode, with an optical power tuning range of at least 10 dB down from maximum power, and supports modulation from 0.15 to 2 kHz.

Platform

The mSRC is part of the MAP LightDirect module family, a set of single-function modules that also includes optical attenuators, polarization scramblers, power meters and spectrum analyzers. The mSRC-C2 is compatible with all current MAP-300 and MAP-200 chassis. The MAP platform is LXI compliant and offers SCPI-based automation drivers, PC-based management tools and a web-enabled multiuser graphical interface with summary and detailed views for laboratory and manufacturing use.

Key Features

Dual 1310 nm high power SLED source with individual outputs
Output optical power ≥ 10 dBm
Optical power stability of ±0.01 dB over 15 minutes
TEC stabilized emitter
Internal optical isolator to reduce dependence on external reflections
Constant current or constant power control mode
Optical power tuning range ≥ 10 dB from maximum power
Modulation from 0.15 to 2 kHz with 1 Hz setting resolution
Single mode fiber with FC/APC connectors
Compatible with all current MAP-300 and MAP-200 chassis
Class 1M laser product per IEC 60825-1 (2014) when installed in a MAP chassis

Specifications

Optical Parameters

Center Wavelength	1310 nm Defined as per IEC 61280-1-3 2010 clause 8.2; measurements after a minimum of 30 minutes warm-up
Wavelength Tolerance	±10 nm
Spectral Width (FWHM)	< 60 nm Measured at constant temperature of 23±5°C, at full power
Output Optical Power	≥ 10 dBm Measured at constant temperature of 23±5°C, at full power
Optical Power Stability for 15 min	±0.01 dB Measured at constant temperature of 23±5°C, at full power
Spectral Ripple (RB = 0.1nm)	0.40 dB
Optical Power Tuning Range	≥ 10 dBm Printed as dBm in the high power table; the datasheet states ≥ 10 dB for standard power versions and the page states 10 dB of power tuning range
Power Control Mode	Constant Current or Constant Power
TEC Stabilized	Yes
Modulation	0.15 to 2 kHz
Modulation Setting Resolution	1 Hz
Modulation Accuracy	±0.5 Hz
Fiber Type	Single Mode Fiber
Connector Type	FC/APC
Configuration	Dual 1310 nm high power SLED source with FC/APC Connectors

General Specifications

Operating Temperature	10 to 40 °C (50 to 104 °F)
Storage Temperature	-30 to 60 °C (-22 to 140 °F)
Operating Humidity	Maximum 85% Relative Humidity, non-condensing from 10 to 40 °C/50 to 104 °F
Dimensions (W x H x D)	4.06 x 13.26 x 37.03 cm (1.6 x 5.22 x 14.58 in)
Weight	1.3 kg (2.86 lb)

Compliance

Safety and Standards	Complies to CE, CSA/ UL/IEC61010-1, LXI Class C requirements, meets the requirements of Class 1M in standard IEC 60825-1 (2014), and complies with 21 CFR 1040.1 except deviations per Laser Notice No. 50 When installed in a MAP chassis
Chassis Compatibility	Compatible with all current MAP-300 and MAP-200 chassis

Specifications are taken from the manufacturer's documentation. See the datasheet for complete and current values.

Applications

Broadband source for use with optical spectrum analyzers
CWDM component measurements
General purpose and interferometry applications
Insertion loss testing
General power sensor or path loss calibration

Options & Accessories

Option	Description
CleanBlastPRO	CleanBlastPRO fiber end-face cleaning system — Optional inspection and cleaning tool for removing dirt and debris from connectors in most common applications.
FiberChek	FiberChek probe microscope — Optional one-button, fully autonomous handheld fiber inspection probe.
P5000i	P5000i fiber microscope — Optional automated fiber inspection and analysis probe with PASS/FAIL capability for PCs, laptops, mobile devices and VIAVI test solutions.
AC500	FC/PC-FC/PC Universal Connector Adapter — Replacement mating sleeve
AC501	FC/PC-SC/PC Universal Connector Adapter — Replacement mating sleeve
AC502	FC/APC-FC/APC Universal Connector Adapter — Replacement mating sleeve
AC503	FC/APC-SC/APC Universal Connector Adapter — Replacement mating sleeve