Network Master MU909060A1 Gigabit Ethernet Module with One SFP Slot and One RJ-45 Port

Gigabit Ethernet module for the MT9090A Network Master with one SFP slot and one RJ-45 port for 10/100/1000 Mbps field testing.

Interface configuration: Gigabit Ethernet Module with one SFP port and 1 electrical RJ-45 port. One optical module can be installed
Electrical interfaces: 10/100/1000 Mbps RJ 45 (10BASE-T, 100BASE-TX, 1000BASE-T)
Optical interfaces: 100 or 1000 Mbps LC connector (100BASE-FX, 100BASE-LX, 1000BASE-SX, 1000BASE-LX or 1000BASE-ZX)
Duplex modes: Full duplex. Electrical 10/100 Mbps also half duplex

Datasheet

Overview

The Anritsu MU909060A1 is a Gigabit Ethernet module for the MT9090A Network Master mainframe. It has one SFP slot and one electrical RJ-45 port. Installed in the compact, battery-powered Network Master, it provides Gigabit Ethernet testing for the installation, maintenance and troubleshooting of Ethernet communication lines, including bandwidth verification, connectivity testing and service availability verification.

The tester is designed for field use. It has no fans or vents, is ready for measurement in about 15 seconds, and provides up to 3 hours of testing on a single charge, depending on configuration and setup. A 4.3-inch wide-screen color display shows results with color-coded graphical symbols, and a Test Automator lets users set up a sequence of tests. Setups can be stored and distributed to other instruments through the USB port.

Testing capabilities

For installation, commissioning and QoS verification, the module generates traffic, including VLAN-tagged traffic, and supports BER testing, performance statistics and QoS statistics. Ping, traceroute, electrical cable diagnostics and service disruption time measurement are included. Optional software adds automated RFC 2544 testing, with end-to-end testing between two units, as well as ITU-T Y.1564 multi-service testing, Multistream, Stacked VLAN, MPLS, Channel Stats and Remote GUI operation through a web browser.

Two-port operation

Both ports can be used at the same time, which shortens testing of multiple ports. They also allow pass-through monitoring and bidirectional monitoring. Test results can be exported as PDF or CSV reports.

Key Features

One SFP slot and one electrical RJ-45 port; one optical module can be installed
Ping test, traceroute test and electrical cable diagnostics
Two ports work simultaneously, including pass-through test and in-line monitoring
Optional automated ITU-T Y.1564 testing of multiple simultaneous traffic streams
Optional automated RFC 2544 testing including end-to-end testing
Stacked VLAN (Q-in-Q), MPLS, IPv4 and IPv6 supported
Test Automator for running sequences of tests
Channel Stats option identifies error streams, top talkers and network attacks
Service disruption time measurement for VoIP and IPTV
Optical power level check and electrical cable test for physical layer testing
Pass/Fail identification and graphical result display
PDF and CSV report generation
4.3-inch high-resolution wide-screen color display readable indoors and outdoors
Ready for measurement in about 15 seconds
Up to 3 hours of battery operation depending on configuration
Fanless, ventless rugged design
Modular platform based on the MT9090A mainframe

Specifications

Ethernet Interfaces

Interface configuration MU909060A1	Gigabit Ethernet Module with one SFP port and 1 electrical RJ-45 port. One optical module can be installed
Electrical interfaces	10/100/1000 Mbps RJ 45 (10BASE-T, 100BASE-TX, 1000BASE-T)
Optical interfaces	100 or 1000 Mbps LC connector (100BASE-FX, 100BASE-LX, 1000BASE-SX, 1000BASE-LX or 1000BASE-ZX)
Duplex modes	Full duplex. Electrical 10/100 Mbps also half duplex
Test configurations	Monitor/Generate, Pass through, Reflector
Supported encapsulations	EtherType II (DIX v.2), IEEE 802.3 with 802.2 (LLC1), IEEE 802.3 with SNAP

Optical Modules

1000BASE-SX 850 nm Multi Mode	Min. input sensitivity –17 dBm, 770 nm to 860 nm; Output power –9.5 to –1.5 dBm, 830 nm to 860 nm Correct functioning can only be guaranteed with optical modules from Anritsu for the MU909060A. Modules with extended temperature range (up to +85°C) must be used.
1000BASE-LX 1310 nm Single Mode	Min. input sensitivity –20 dBm, 1260 nm to 1580 nm; Output power –10 to –3 dBm, 1285 nm to 1343 nm
1000BASE-ZX 1550 nm Single Mode	Min. input sensitivity –22 dBm, 1260 nm to 1580 nm; Output power –3 to +5 dBm, 1480 nm to 1580 nm
100BASE-FX 1310 nm Multi Mode	Min. input sensitivity –31 dBm, 1260 nm to 1570 nm; Output power –20 to –14 dBm, 1270 nm to 1335 nm
100BASE-LX 1310 nm Single Mode	Min. input sensitivity –28 dBm, 1260 nm to 1570 nm; Output power –15 to –8 dBm, 1261 nm to 1360 nm

Traffic Generation/Monitor

Line rate	Variable line rate traffic generation, up to full line rate
Traffic shaping	Constant, Burst, Ramped
Frame size	Constant, Stepped or Random length; adjustable frame size from 46 to 10,000 bytes
Addressing	Configurable MAC/IP source and destination addresses (supports IPv4 and IPv6), UDP/TCP address and DSCP/TOS byte Request IP source address from a DHCP server (On/Off)
VLAN / MPLS	User defined up to 3 level VLAN ID and VLAN priority (Option); User defined up to 3 level MPLS label (Option)
Other generation functions	User defined traffic mix of unicast and broadcast frames; Generate and respond to pause frames; Answer incoming ARP request (On/Off); MAC /IP address swapping (reflector configuration)
Test result (Current/Cumulative)	Total frame, Total bit, Utilization, Throughput, Broadcast frame, Error frame, Frame loss, Frame loss rate
Graph	Tx utilization, Tx throughput, Rx utilization, Rx throughput, Error frame
Service Disruption Time	Min, Max, Average, Count, Total time, Total SDT (%) , Last frame received (interval) timestamp
Channel Stats (Option)	Total frame, Total bit, Error, Frame size distribution of up to 63 filtered streams

Measurements

Status	Link status, Signal and Frames present (utilization), Errored frames, Rx/Tx frame count, Link time, Remote fault, Speed, Full/Half duplex, MDI/MDIX, Interface type, Link partner abilities (Pause capable and Asymmetric pause capable), Local clock (1000 Mbps), DHCP lease time, Optical level for optical interfaces
Event log	The instrument logs major events during a test with a 1 sec. resolution time stamp. Logged events include: Link/No link and Test Start/Stop
Report generation	Generation of test result reports as pdf-files. The report may be customized with a user logo and comments.

Tests

Electrical cable test MU909060A1, MU909060A2	Detection of MDI/MDIX mode, Link speed and status, Cable status and distance to fault (if any), Polarity. For 1000 Mbps also skew; Pin mapping: Tx/Rx for 10/100 Mbps, DA, DB, DC, DD for 1000 Mbps
BER test patterns	FOX, all 0, all 1, 0101, PING, PRBS 9, PRBS 11, PRBS 15, PRBS 20, PRBS 23, PRBS 29, PRBS 31, HF test pattern, CRPAT, JTPAT, SPAT Pattern generation: Unframed, Framed with IP header or Framed with IP and TCP/UDP header. Detection of sequence errors and loss of sequence synchronization.
Ping test	Round Trip Time (RTT); Supports IPv4 and IPv6 addressing; Answer incoming Ping requests (On/Off)
Traceroute test	Setup: Number of Attempts, Max number of hops, Number of ping each host, Timeout; Result: Number of hop, Host IP address, Number of Received/Lost replies, Min/Max/Average time
ITU-T Y.1564 Test (Option)	Test mode: Single Ended test, Switch/Router test, End-to-End test; Configuration Test: Up to 32 services, Up to 6 steps with CBS, EBS; Service Performance Test: Up to 32 services Test report: Y.1564 Appendix II compliant (CSV or PDF)
RFC 2544 Installation and Commissioning Tests (Option)	Single ended network test and Switch/Router test modes: Throughput and utilization, Frame loss, Latency, Packet jitter, Back-to-back frames (burstability); End-to-End network test mode (two MU909060A in an in-band control setup): Throughput and utilization, Frame loss, Back-to-back frames (burstability); Router latency test mode: IP ping based latency, IP ping based packet jitter
Multistream Test (option)	Up to 8 streams can be activated on the Ethernet line Per stream: Frame loss count/rate, Frames and bytes received, Frames and bytes transmitted
HTTP/FTP test	Test mode: HTTP, FTP; Result: Received/Total file size, Min/Max/Average throughput Setup: Target directory, Download file name, Authentication
Reflector delay	2.44 μs @1000 Mbps, 5.16 μs @100 Mbps, 31.93 μs @10 Mbps Maximum internal delay when instrument is in reflector configuration

General

Internal memory	40 MB For storage of results, setups and screen shots
Service interface	Two USB 1.1 (One type A for USB memory stick, One type B for USB mass storage)
Display	4.3-inch color LCD (480 × 272 pixels), with LED back light, transmissive
Language	English, Japanese, Chinese (Simplified, Traditional), Spanish, German, Korean, French, Italian, Portuguese
Startup time	about 15 seconds

Power

Battery	Dedicated battery pack or 4 AA Ni-MH
Operating time	Up to 3 hours depending on configuration and test setup
Charging time	4 hours while power off (typ.), Temperature: +10° to +30°C
Power supply	AC adapter: 9 V(dc), 100 V(ac) to 240 V(ac), Frequency: 50 Hz/60 Hz

Physical

Dimensions and mass MU909060A1	190 (W) × 96 (H) × 30 (D) mm, <600 g Module; MT9090A mainframe: 190 (W) × 96 (H) × 18 (D) mm, <200 g

Environmental

Operational temperature range	0° to +40°C, humidity ≤85%, No condensation
Storage temperature range	–25° to +60°C, humidity ≤80%, No condensation
Vibration	IEC 60 068-2-6 Fc and IEC 60 068-2-64 Fh
Ingress protection rating	IEC60529 IP51

Compliance

CE	EMC 2014/30/EU, EN61326-1, EN61000-3-2; LVD 2014/35/EU, EN61010-1; RoHS 2011/65/EU, (EU) 2015/863, EN IEC 63000: 2018
UKCA	EMC S.I. 2016 No.1091, EN 61326-1, EN61000-3-2; LVD S.I. 2016 No.1101, EN 61010-1; RoHS S.I. 2012 No.3032, EN IEC 63000:2018
Laser safety	IEC 60825-1: 2014 CLASS 1 Complies with 21CFR1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed.3., as described in Laser Notice No. 56, dated May 8, 2014

Specifications are taken from the manufacturer's documentation. See the datasheet for complete and current values.

Applications

Gigabit Ethernet installation and commissioning
Ethernet maintenance and troubleshooting
QoS verification
Carrier Ethernet testing
Mobile backhaul testing
VoIP and IPTV service disruption testing
Multiple-port network deployment

Included

W3173AE Gigabit Ethernet Tester Quick Start Guide
Z1234A Network Master Gigabit Ethernet Tester CD

Options & Accessories

Option	Description
MU909060A1-001	RFC 2544 Test (for MU909060A1) — Including End-To-End testing with master/slave control
MU909060A1-002	Multistream (for MU909060A1) — Up to 8 streams simultaneous testing
MU909060A1-003	Stacked VLAN (for MU909060A1) — Up to 3 levels tagged VLAN support
MU909060A1-004	MPLS (for MU909060A1) — Up to 3 MPLS labels support
MU909060A1-005	Remote GUI (for MU909060A1) — Controlling MT9090A via Web browser. Requires J1480A USB-Ethernet Converter (sold separately)
MU909060A1-006	Channel Stats (for MU909060A1) — Analyzing error streams, top talkers, network attacks
MU909060A1-007	Y.1564 Test (for MU909060A1) — New methodology to reduce testing time
MU909060A1-301	RFC 2544 Test Retrofit (for MU909060A1)
MU909060A1-302	Multistream Retrofit (for MU909060A1)
MU909060A1-303	Stacked VLAN Retrofit (for MU909060A1)
MU909060A1-304	MPLS Retrofit (for MU909060A1)
MU909060A1-305	Remote GUI Retrofit (for MU909060A1) — Requires J1480A USB-Ethernet Converter (sold separately)
MU909060A1-306	Channel Stats Retrofit (for MU909060A1)
MU909060A1-307	Y.1564 Test Retrofit (for MU909060A1)
MU909060A1-ES210	2 Years Extended Warranty Service (for MU909060A1)
MU909060A1-ES310	3 Years Extended Warranty Service (for MU909060A1)
G0240A	1000 Mbps SX SFP — 850 nm multimode, LC connector (optical)
G0241A	1000 Mbps LX SFP — 1310 nm single mode, LC connector (optical)
G0242A	1000 Mbps ZX SFP — 1550 nm single mode, LC connector (optical)
G0243A	100 Mbps FX SFP — 1310 nm multimode, LC connector (optical)
G0244A	100 Mbps LX SFP — 1310 nm single mode, LC connector (optical)
G0246A	10/100/1000 Mbps RJ-45 SFP (electrical)
Z1580A	Protector & Soft Case — The protector (B0663A) and standard soft case (B0601B) form a set
B0600B	Hard Case — Accommodates two mainframes (with or without fitted protector) and accessories
B0602B	Deluxe Soft Case (for MT9090A) — Full Network Master operation without removal from the case
J1402A	Car Plug Cord
W3166AE	MU909060A1/A2/A3 Operation Manual (Hardcopy – English version)
J1480A	USB-Ethernet Converter — Requires MU909060Ax-y05 Remote GUI (sold separately)