VIAVI mX3 MX3-QSFP28-4-100A 100G QSFP28 4-Port Test Module

VIAVI mX3 4-port QSFP28 TestCenter test module, base package configured for 100G only operation.

100G media: 100GBASE-SR4, 100GBASE-CR4, 100GBASE-LR4, plus additional MSA PMDs
50G media: 25/50G Consortium 50GBASE-CR2
40G media: 40GBASE-SR4, 40GBASE-CR4, 40GBASE-LR4
25G media: 802.3by 25GBASE-CR, 25GBASE-CRS, 25GBASE-SR

Datasheet

Overview

The VIAVI MX3-QSFP28-4-100A is a QSFP28 High Speed Ethernet test module for the VIAVI TestCenter platform, part of the TestCenter 100G multi-speed family. TestCenter 100G solutions validate data center, service provider and enterprise networks built on 100G Ethernet, covering performance validation, interoperability testing and regression testing.

The QSFP28 interfaces in the family use four 25G electrical lanes. FPGA logic switches the packet generation and analysis engine between 100, 50, 40, 25 and 10G operation, depending on the speeds in the purchased base package. Hardware speed options can add speeds to a base package after purchase.

The modules install in the VIAVI N12U and N4U chassis. They take their transmit line clocking and time-stamping from the chassis control modules, and separate chassis can be synchronized through a timing chain, GPS or CDMA, or NTP and PTP packet-based methods.

TestCenter protocol emulation is licensed separately. It covers enterprise and data center switching (OpenFlow, routing, multicast and bridging) and service provider protocols, including routing and MPLS, access, Carrier Ethernet and mobile backhaul.

Key Features

Mode-switching QSFP28 interfaces for 100, 50, 40, 25 and 10G operation, depending on the base package
Clause 74 BASE-R FEC, Clause 91 RS-FEC and Clause 108 RS-FEC can be enabled or disabled
Auto-Negotiation and Link Training for 100G, 50G, 40G and 25G
QSFP28 to SFP28 breakout cable options
Frame time stamp resolution of 2.5 ns
Hardware speed options to add speeds to a base package after purchase
Separately licensed VIAVI TestCenter Layer 2–3 protocol emulation packages
Software-based MACsec support across all ports
Two multi-core Intel Xeon Class CPUs per module for stateful protocol emulation
Autonomous Flow Tracking (AFT) supported in 100G speed mode

Specifications

Media Support and FEC Options

100G media	100GBASE-SR4, 100GBASE-CR4, 100GBASE-LR4, plus additional MSA PMDs Support varies by module speed mode
50G media	25/50G Consortium 50GBASE-CR2
40G media	40GBASE-SR4, 40GBASE-CR4, 40GBASE-LR4
25G media	802.3by 25GBASE-CR, 25GBASE-CRS, 25GBASE-SR
10G media	10GBASE-SR, 10G Copper DAC
Breakout	QSFP28 to SFP28 breakout cable options
Auto-Negotiation and Link Training	Auto-Negotiation and Link Training for 100G, 50G, 40G and 25G
FEC	Clause 74 BASE-R FEC, Clause 91 RS-FEC, and Clause 108 RS-FEC
50G Consortium FEC	25/50G Consortium 50GBase-R FEC CL74, 25/50G Consortium 50GBase RS-FEC CL91
IEEE 25G FEC	IEEE 25GBASE CR CL74, CL108, CR-S CL74, SR FEC CL108
25G Consortium FEC	25/50G Consortium 25GBase-R FEC CL74, 25/50G Consortium 25GBase RS-FEC CL91

Port Configuration

Port density MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	4-port QSFP28 module options
User reservation MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Per-port reservation
Maximum support speed	100G Only
Maximum ports per slot	4
Maximum ports per N12U chassis	48
Maximum ports per N4U chassis	8

Timing and Synchronization

Default time source	Stratum-3 rated oscillator Modules get transmit line clocking and time-stamping from the control modules on the N12U and N4U chassis
Frame time stamp resolution	2.5 ns
External time sources	GPS and CDMA-based; IEEE 1588v2 and NTP packet-based; TIA/EIA-95B-based
Inter-chassis timing chain synchronization	± 20 ns Ports in the same chassis are locked to the internal timing source

Traffic Generation and Analysis

Transmit / receive streams per port MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	64k TX and 128k RX for all speeds
VFDs MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	6 VFDs available for each 1k (100G) and 512 (50/40/25/10G) stream templates
Route insertion table MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	4 m route insertion table entries for all speeds
Scheduler modes MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Port Based, Rate Based, Priority Based, Manual Mode
Frame length range and controls MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	100% line rate for frames of 58-16383 bytes controlled by fixed, increment, decrement, random and IMIX modes
Statistics MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Nearly 50 transmit stats per port reported in real time; over 40 real-time measurements per stream including advanced sequencing, latency, jitter and data integrity
Capture MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	1 MB per 100G or 40G port; 512 kB per 50G port; 256 kB per 25G port Capture software includes trigger and filtering controls
Histograms MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Port-level histogram modes for latency, jitter, interarrival time, frame length, sequence run length and sequence difference check
Protocol CPUs MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Each module features two, multi-core, Intel Xeon Class CPUs
MACsec support MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	Same MACsec feature set on MX3-QSFP28-4 module that is present on other VIAVI hardware

Physical and Environmental

Operating temperature MX3-QSFP28-4-40A, MX3-QSFP28-4-50A, MX3-QSFP28-4-100A, MX3-QSFP28-4-125A, MX3-QSFP28-4-150A, MX3-QSFP28-4-175A, MX3-QSFP28-4-225A	15°C - 35°C, 20% - 80% RH (non-condensing)

Specifications are taken from the manufacturer's documentation. See the datasheet for complete and current values.

Applications

Service provider core and edge routers
High-capacity multiservice routers
Data center top of rack, spine and core switches
Carrier Ethernet service validation
RFC 2544, RFC 2889 and RFC 3918 benchmarking

Options & Accessories

Option	Description
ACC-6095A	Optical Transceiver QSFP28 100GBASE-SR4 MMF 850NM
ACC-6096A	Optical Transceiver QSFP28 100GBASE-LR4 SMF 1310NM
HWO-MX3-QSFP28-4-50G	50G Hardware Speed Option for MX3-QSFP28-4
HWO-MX3-QSFP28-4-40G	40G Hardware Speed Option for MX3-QSFP28-4
HWO-MX3-QSFP28-4-25G	25G Hardware Speed Option for MX3-QSFP28-4
HWO-MX3-QSFP28-4-10G	10G Hardware Speed Option for MX3-QSFP28-4
SWO-MX3-QSFP28-4-MACSEC	MACsec Software on MX3-QSFP28-4 100G Test Modules
BPK-1407	Autonomous Flow Tracking (AFT) Package — Only supported on mX3 4-port 100G speed mode